How To Make Beaded Jewellery

Cut the chain into two lengths for each earring aprox 3 or 4 cms.   Place 7 of the 6mm pearls onto headpin, make a loop, and attach these straight onto the chain.   Thread onto an eye pin a beadcap 10mm pearl another bead cap and 4mm Swarovski make a wrapped loop. Attach the chain to the end of the eyepin, by opening the loop a little way, twist the loop open rather than pull, and twist it shut. Attach the earwire to the top of the earring, tie the... Read More

 Cut two lengths of tiger tail approx 20 cms long, thread one length through one side of the watch,  so you have two lengths on either side the same. On one side thread on a stardust bead Swarovski pearl  another stardust, pearl and stardust, repeat on the other side.. Thread onto both wires a 6mm Swarovski, now open the wires and repeat the first pattern, thread on a 6mm, and then 2 stardust onto both wires. Thread on a crimp and clasp onto both wires, thread both wires over the... Read More

Using 10 headpins, on each headpin you will place a seed bead and then one of the Swarovski bicones or a pearl, so you will have 5 headpins with 6mm bicones and 5 headpins with pearls. Do the same with the five 4mm bicones. Turn a loop on all these headpins. On one side of the ring attach to the first loop a bicone, on the next loop attach a pearl alternate until you get to the last loop and repeat on the other side , this time starting with... Read More

Cut the belcher chain to approx 14cm Place on 4 silver headpins 1 x cezch faceted oval and 1 x swarovski 4mm crystal, and make a wrapped loop. Using 4 antique brass headpins place on the 8mm pearl and then the 6mm pearl, make a wrapped loop. Attach each a leaf on to a (how to open) silver jump rings and place along the belcher chain as evenly spaced out as you can. Now attach the cezch ovals you made in step 2 on the chain in between the leaves... Read More

Place each of these set of beads in order shown on 2 eyepins and make a loop on each. [half] 1x 6mm Vintage Gold pearl, 1x 10mm Emerald soft touch, 1x 6mm Vintage Gold pearl, 1x 6mm Vintage Gold 1x 4mm golden shadow, 1x 12mm Glass Discs Teal , 1x 4mm golden shadow, 1x 6mm Vintage Gold pearl, 1x 8mm Antique Brass , 1x 6mm Vintage Gold pearl, 1x 4mm Indian Sapphire, 1x 6mm Vintage Gold pearl, 1x 4mm Indian sapphire, [/half] [half_last] [/half_last]   Attach each section in the... Read More

, Place the beads below on 4 headpins, in the order shown and then turn a loop on each to finish. 1x  4mm Swarovski Indian sapphire 1x  Emerald soft touch bead 1x  4mm Indian sapphire , Place the beads below on 5 headpins, in the order and then turn a loop on each to finish 1x  Swarovski pearl 1x Gold spacer bead 1x Golden shadow 4mm Swarovski Thread on a jump ring to all 9 headpins you have made, and attach them along the bracelet. , Open a jump ring,... Read More

Create these lovely Heart pendants using Czech glass beads, they are simple to make and by adding your own choice of chain or thread, you can make this into a stunning necklace.  [half]  Thread the needle. Knot your beading thread onto the bottom of your heart. Take your needle through the back to the front, you can leave a longer piece through the back and ties into a knot with the long side of the thread. [/half] [half_last] [/half_last] [half]  Thread the needle back through the hole, then pick up... Read More

Create this stunning ring kit, using Swarovski crystal bicones and pearls.  Threaded onto the mesh ring using nylon and finished off with opaque Miyuiki seed beads. 1 Take approx 1m of nylon, thread through the centre hole of the sieve so that approx 7cm protrudes from the back. Thread the other end through a hole next to it and knot the two ends twice at the back, then thread back up through the centre hole. Do not trim the short end; you will need it later to secure the finish.... Read More

First cut the chain into different lengths of your choice.   Place the all beads onto all the headpins and turn a loop on each headpin.   Attach the 6mm rings to all the charms how to open a jump ring [toggle title=” Technique: Open A Jump Jing “]  [half] [/half] [half_last]  With your left hand hold the jump ring steady using one of the flat nose pliers. Now using another pair of flat nose pliers, with your right hand, bring them towards you to open. [/half_last]   [half] [/half] [half_last] To make... Read More

  [half] Order the beads as shown above, then insert the wire into the hole at the top of the earring, to secure pinch the tube using the round nose pliers. To finish open the loop on the fishhook and attach to the earring hoop and close. [/half] [half_last] [/half_last]